Install Ulang Mikrotik + Netinstall
Netinstall
adalah program under windows yang diggunakan untuk install,upgrade atau
install ulang dalam hal ini Operating System Mikrotik.
Untuk installasi menggunakan Netinstall yang perlu di siapkan adalah :
- PC dengan interface Ethernet dan Serial / COM
- Kabel Null Modem.
- Kabel UTP
- Routerboard atau dedicated PC MIKROTIK
Software Neinstall, Package mikrotik yang akan di install yang bias di download dihttp://www.mikrotik.com/download.html
- Konek Routerboard ke PC dengan menggunakan UTP sekaligus kabel null modem.
- Persiapkan PC dan jalankan Netinstall.
Tekan Net booting kemudian isikan ip address routerboard yang akan di install.
- Persiapkan Hyperteminal untuk koneski via Serial
- Buka Hyperteminal koneksi menggunakan COM1 atau COM2 Set Properties seperti di gambar.
Set rourterboard supaya booting via Ethernet.
1. Tampilan dari hyperterminal.
RouterBoard 532A
CPU frequency: 399 MHz
Memory size: 64 MB
Memory size: 64 MB
Press any key within 2 seconds to enter setup..
2. Tekan sembarang tombol dalam waktu 2 detik untuk masuk ke bios routerboard
maka akan tertampil seperti dibawah.
RouterBOOT-2.9
What do you want to configure?
d – boot delay
k – boot key
s – serial console
o – boot device
u – cpu mode
f – try cpu frequency
c – keep cpu frequency
r – reset configuration
e – format nand
g – upgrade firmware
i – board info
p – boot protocol
t – do memory testing
x – exit setup
your choice: x – exit setup
What do you want to configure?
d – boot delay
k – boot key
s – serial console
o – boot device
u – cpu mode
f – try cpu frequency
c – keep cpu frequency
r – reset configuration
e – format nand
g – upgrade firmware
i – board info
p – boot protocol
t – do memory testing
x – exit setup
your choice: x – exit setup
3. Tekan o untuk , memilih sesi booting.
Select boot device:
e – boot over Ethernet
* n – boot from NAND, if fail then Ethernet
c – boot from CompactFlash only
1 – boot Ethernet once, then NAND
2 – boot Ethernet once, then CompactFlash
o – boot from NAND only
b – boot chosen device
your choice: e – boot over Ethernet
* n – boot from NAND, if fail then Ethernet
c – boot from CompactFlash only
1 – boot Ethernet once, then NAND
2 – boot Ethernet once, then CompactFlash
o – boot from NAND only
b – boot chosen device
your choice: e – boot over Ethernet
Tekan e untuk Booting via Ethernet
Kemudian tekan x untuk exit kemudian booting
- Setelah Reboot maka akan tertampil seperti ini:
writing settings to flash… OK
RouterBOOT booter 2.9
RouterBoard 532A
CPU frequency: 399 MHz
Memory size: 64 MB
Memory size: 64 MB
Press any key within 2 seconds to enter setup..
trying bootp protocol…. OK
Got IP address: 192.168.1.1
resolved mac address 00:E0:29:58:34:5C
transfer started ……………….. transfer ok, time=1.12s
setting up elf i
setting up elf i
trying bootp protocol…. OK
Got IP address: 192.168.1.1
resolved mac address 00:E0:29:58:34:5C
transfer started ……………….. transfer ok, time=1.12s
setting up elf i
setting up elf i
Welcome to MikroTik Router Software remote installation
Press Ctrl-Alt-Delete to abort
Press Ctrl-Alt-Delete to abort
mac-address: 00:0C:42:0F:FF:99
software-id: 94HI-3TT key:
vOHPk/4znX8nskLninMIFT4bEdqfCQoLIQg6RwPRdI9n3vrqa2Cj1WEKffivJflfDUl1YUCy+8tHUtx=
vOHPk/4znX8nskLninMIFT4bEdqfCQoLIQg6RwPRdI9n3vrqa2Cj1WEKffivJflfDUl1YUCy+8tHUtx=
Waiting for installation server…
Persiapkan lagi PC dan Netinstall
Pilih routeros package yang akan di install kemudian tekan install
Tunggu sampai selesai kemudian reboot
Di hyperterminal
Ubah lagi sesi booting ke NAND kemudian reboot..tunggu hingga booting selesai
Routerboard teleh selesai di install
0 Komentar